Personal Protective Equipment (PPE)

Single Use
Ambidextrous

Storage

Store in cool dry place.

Do not store gloves where temperatures may rise above 40 C(104 F).

Do not store in highly humid or damp areas.

Shield from direct sunlight, fluorescent lighting, x-rays, moisture and ozone.

Caution

Nitrile gloves are not intended for use as a chemical barrier.

Do not use these gloves for protection from hazardous chemicals.

Available in 2
practical sizes !

80 Wipes

GLDI-520-12S80

160 Wipes

GLDI-520-61S60

STRONG DEPENDABLE WIPES

Effective disinfectant without residue.

INFORMATION

1-800-921-5527
info@superiorsols.com
www.superiorsols.com

DISINFECTANT WIPES

Sany+ Disinfectant Wipes are pre-moistened wipes that kill 99.9% of Bacteria in just 60 Seconds! Clean and disinfect in one easy step, just pull, wipe and toss.

Drections:

Use one Sany+ Disinfectant Wipe to disinfect.
Flip open dispensing tab and remove lid. Thread
center wipe corner through slits in lid center.
DO NOT PUSH FINGER THROUGH OPENING.
Replace lid. Dispense wipes by pulling out at an
angle. The next wipe pops up automatically.
Snap flip lid down when finished, to retain
moisture. Dispose of used wipes in trash.
Do not flush.

Disinfecting

To disinfect hard, non-porous surfaces,
thoroughly wet the surface to be treated.
Treated surface must remain visibly wet for
disinfecting. Use enough wipes for treated
surface to remain visibly wet for 5 minutes.
For heavily soiled surfaces, clean before
following disinfecting instructions.

Please read before use!

Summary of Infrared Thermometer

Thank you for choosing our Infrared Thermometer. The PC868 Infrared Thermometer is used to measure an objects temperature based on the relationship between temperature and measurable infrared radiation. Simply aim the unit’ s probe toward the surface to be measured to obtain a quick and accurate temperature.
To ensure proper use,please be sure to read this user manual carefully,paying close attention to the safety precautions.
• In order to use this product correctly,please read the user manual before use.
• In order to properly use this product,please carefully read the full text of this manual before using, in particular the “safety precautions"section.
• Please keep the instructions on the side for easy checking.

Basic principles:
All objects above absolute zero temperature emits certain percentage of infrared radiation energy based on its temperature.The amount of the radiation energy and the distribution of thewavelengthhaveverycloselyrelationship.Whenhumanforehead’stemperaturein36-37°C,it emits wavelength 9-13um of infrared radiation. Based on this principle, according to the relationship between surface forehead temperature and human forehead’s temperature,we are able to measure the human forehead’s actual temperature through measuring surface forehead temperature.

Safety precautions

Warning

• Use of this thermometer is not intended as a substitute for consultation with your physician. It is dangerous for user to perform a self-evaluation and self-treatment based on the measuring result. Be sure to follow doctor’s instruction.
• Keep the thermometer out of reach of children. For accidental swallow of battery or other component, please consult the doctor at once.
• Don't throw the battery into fire.

Notice

• The device is precision instrument,don’t drop,tramp or impose any vibration or impact on the thermometer.
• Do not touch the lens of the probe with your fingers,and do not dissemble the device by yourself.
• Before measuring forehead temperature,make sure the hair re-moved, sweat dried.
• After you do some exercise,eating and bathing,you should stay still indoor about 30 minutes before measurement.
• To make the measurement data reliable and stable, when ambient temperature varies a lot,the thermometer should be placed indoors for about 30 minutes before using.
• When we measure somebody continuously,the temperature should be measured every minute,if you need to measure yourself Continuously for a short time,there are some slight errors when you read the temperature,which is a normal phenomenon.At this time,we should choose the average.We recommend that you measure yourself continuously maximum of three in a unit of time,and because the temperature of the human will conduct to the thermometer,it may affect the accuracy of measurement.
• There is no absolute standard about the temperature of the human, so please try to collect the recording of Individual temperature in the usual,as a reference for having a fever or not.
• Do not measure the sites of scarred tissue or tissue compromised by skin disorders,because sensing body temperature from sites of scarred tissue or tissue compromised by skin disorders.
• Do not measure the site of forehead temperature if that patients has trauma on forehead.
• Do not measure if that patient is treated with certain drug therapies.
• Do not immerse the device into water or any other liquid,and not directly sunlight exposure.
• Do not use a mobile or mobile or cordless hone near the thermometer when measuring.
• Body temperature may increase in the drug with in the effort time limit. Please don’t measure.
• In order to ensure the accuracy of measurement data,please don’t take measurement of body temperature in strong electro- magnetic interference environment (such as microwave, high frequency equipment operation environment).
• Do not disassemble, repair, or modify the unit.
• This thermometer only a personal device,please do not user with others.
• Not touch the battery output when measuring.
• The thermometer must be stored according to the technical specifications.
• The materials (ABS) of expect contact with patient had passed the ISO 10993-5 and ISO 10993-10 standard test,no toxicity,allergy and irritation reaction. The are compliance with the MDD requirements. Based on the current science and technology, other potential allergic reactions are unknown.
• The patent is an intended operator. The patient can measure, read data and replace battery under normal circumstances and maintain the device and its accessories according to the user manual.
• ThedeviceisnotintendedforPATIENTtransportoutsideahealthcarefacility.

Recommendations

1) Don’t use this thermometer for other purposes.
2) It is forbidden to leave the product exposed to any chemical solvent, direct sunshine or high temperature.
3) Don’t expose the thermometer under direct sunlight longtime so as not to damaged the battery.
4) Do not measure while talking on the phone.
5) Please report to MANUFACTURER if any unexpected operation or events occur.

Intended use

This thermometer is intended with non-contact to measurement forehead temperature at home or hospital,including anyone,such as infants, children and adults.
For the safety reason,children or the baby’s temperature must be measured by parent or adults.

Temperature measurement mode and range description

The infrared thermometer has the following measurement mode:
1) Forehead temperature measurement mode--measure the skin surface of human forehead’s temperature accurately,taketheplaceoftraditionalmercurythermometerandelectricalthermometer.
2) Object temperature measurement mode—you can measure the surface temperature of object,such as ambient,bathwater and milk temperature etc.

Normal temperature range for different measuring position

Normal forehead temperature range for different ages

NOTE: The normal temperature and difference between the different body parts is individual. The define yours,measure your temperature for atleast 2 weeks at the same ear canal,forehead position and time.
NOTE: When consulting your physician, communicate that the infrared thermometer PC 868 temperature is a temperature measured which position,note the individual’s normal infrared thermometer PC 868 temperature range as additional reference.
NOTE: Because the forehead temperature is affected obviously by the external environment(eg: environment,air convection and skin tone,etc),we advice that you take the forehead temperature only as reference.

Feature

• Precise non-contact measurements
• User selectable °C or°F
• Set alarm temperature value
• Automatic data hold and auto power save
• Automatic selection range and display resolution 0.1°C(0.1°F)
• 3 colors backlight
• 2 measurement mode: Forehead and surface mode

Overall description

1. IR sensor
3. Mode selection
5. UP button
7. Measurement Trigger

2. LCD display
4. Down button
6. Mode button
8. Battery cover

[LCD display description]

1. Surface mode symbol
2. Body mode symbol
3. Digital readout
4. Battery symbol

5. Memory Symbol
6. Save data readout
7. Temp.°C(Celsius)/°F(Fahrenheit)scale
8. Buzzer symbol

Operation Instruction

[Preparation]

1) Check battery
Replace the batteries to ensure power supply if there is low voltage icon for the thermometer.
2) Check sensor
If have pollution and spray,please clean it.(The cleaning method see the chapter 8 Care and Cleaning for detailed.)
If the sensor’ s lens is damaged, please stop using.
3) Check thermometer
When you press the[Power/Scan]button,the system will have self testing of software and hardware. If there are problems, LCD will display "Err" symbol. Check if the sensor laser is dirty, damaged phenomenon.
4) In order to make the accurate measuring result, put the thermometer in the measurement environment for 30 minutes.
5) Accuracy of unexpected fluctuations in ambient temperature may decrease the measurement results When the thermometer at the same measurement position display at different ambient temperature,or test temperature in front of the air conditioner,it will not be able to obtain accurate results.
6) If you want measure forehead temperature, clean forehead and arrange hair,make sure the forehead is naked and clean,in order to ensure the accuracy of measurement.

[Instruction for use]

Advice for the first use

For stable and reliable results,it is essential to check the infrared thermometer and changes as needed,as follows:

Use

Install batteries

2. For the first use or when inserting new batteries,please wait about 10minutes for the warm-up of the apparatus.
3. If the device is not used for a long time, once you turn it on again,the device will test the room temperature first and will delay turning on for one or two seconds.
4. Select body mode,aim towards the forehead,form distance of 5cm(2in),press the measuring key,the temperature is displayed immediately,accompanied by a beep sound. Making sure there is no hair,perspiration,cosmetic or cap covered on the forehead.

5. If the measurement temperature is 38.0°C or more(can be setting,refer to sub-clause 3)),the sound should be“be-be-be-be-be”5 repid sounds.

6.Select object mode for measuring room temperature,surface temperature etc.

Setting operation

--Range of alarm temperature
When into the“F-2”mode,the range of settable alarm temperature is from 37.6°C(99.7°F)to 43.0°C(109.4°F).
-Range of temperature difference
When into the“F-3”mode,the range of settable temperature difference is from 5°C(9°F) to-5°C(-9°F).

Temperature measuring

--Taking Temperature in Forehead Temperature Mode (Adjusted Mode)
1. Setup the measurement mode to“Body mode”(the setup step see the above “2) Function Setup mode”;
2. Make sure the distance between thermometer and forehead is 3-5 cm,and press the button of[Power/Scan]directly to measure the forehead temperature.
3. When you hear one beep sound,the LCD will show the result.

NOTE:

1. When measuring, if the environment exceed the 10-40°C range will be showing Err;
2. If the measured temperature result is > 32.0°C,the LCD will be showing Lo;
3. If the measured temperature result is > 43.0°C,the LCD will be
showing Hi;
4. If the measured temperature result is >= 38.0°C,the buzzer will be send out“Beep—Beep—Beep”,along one and two short ones.
5. We recommend measurement for 3 times to reference,and keep the interval between the two measurements by 5 minutes atleast.

-Taking Temperature in Surface Temperature Mode(Direct Mode)
1. Setup the measurement mode to“Surface mode”(the setup step see the above “2) Function Setup mode”
2. Aim the probe tip at the object which will be measured.
3. Press [Power/Scans button, then the measurement completed. It will show the measurement data after a “bi”sound.
4. If the measured temperature is higher than 100°C, display “Hi”. If the measured temperature is below 0°C, display“Lo”.

Automatic shutdown

If you do nothing after the temperature measurement completed and 15 seconds later, the thermometer will automatically shutdown.

Memory function

In the power-on state, press the Up/Down button into memory query mode,the LCD will be showing the recorded values or“---“ symbol if not record accompanied with memory M symbol.The PC 868 can restore up to 99 sets data. the query interface can display memory seriaI number,body mode and recorded temperature values.
Remark:The temperature result of surface mode cannot be saved. And the abnormal body temperature result cannot be saved too (such as Lo, Err or Hi).

Backlight function

The backlight will be according to the different measuring temperature to lighting different color . The detailed as below table:

Restore the factory default function

Press the [Setup] button for 5s to restore the factory default status. The factory default setup is "C” and “Body measurement” mode.

Battery installment and replacement

1. When the quantity of electric charge is not sufficient,the icon of low battery will appear on the lower part of the screen. Though the battery still can be used,it would be perfect to replace it.
2. When the quantity of electric charge of the battery is lower than them minimal value,“Lo”symbols will bed is played on the screen, and battery icon flashes and the sound of “Beep” is sent out.
Unless you change a new battery,you cannot use the thermometer to conduct measurement.
3. Operation of changing battery.
4. Take out the old battery: Open the battery cap;put 2 new AAA batteries on with correct cathode direction into the battery seat.

Notice:

◦ Please observe the related national laws of disposing the abandoned battery and don’t litter to the garbage can.
◦ Please take out the battery if the device is not used for long periods of time.
◦ Please don’t put the battery in the fire.

Care and cleaning

• Probe tip (lens) is a most precise part in the thermometer.Please keep clean and entirety in order to assure the accuracy of figure.
• The probe tip and lens are the most delicate part of the thermometer. It has to be clean and intact to ensure accurate readings.
• If the thermometer is ever accidentally used clean the probe and lens as follows:
• Very gently wipe the surface with a cotton swab or soft cloth moistened with alcohol. After the alcohol has completely dried out.
• If the lens is damaged,contact the distributor.
Clean the unit body:
• Use a soft,dry cloth to clean the thermometer display and unit body.
• If very dirty,use a soft with alcohol to cleaning.

Notes:

◦ Don not use abrasive cleaners.
◦ Don’t use other non-recommended methods to perform disinfect.
◦ Non-waterproof, don’t use the abrasive cleaner to clean the product, don’t drop the thermometer in the water or the other liquid.

Maintenance

1) We don ot authorize any institution or individual to maintain and repair of the product. If you suspect that the products have any questions,please contact the manufacturer or distributor to handle the case.
2) The user must not attempt any repairs to the device or any of its accessories. Please contact the retailer for repair.
3) Opening of the equipment by unauthorized agencies is not allowed and will terminate any claim to warranty.
WARNING: No modification of this equipment is allowed!

Calibration

The thermometer is initially calibrated at the time of manufacture.If this thermometer is used according to the use instruction, periodic re-adjustment is not required. If any time your question the accuracy of measurement, please contact distributor or manufacturer, the contact information see last page.

Storage

1) Don’t put the thermometer under the sunshine, high temperature and moist environment or some place which may be get in touch with fire or is vulnerable to vibration.
2) Take out the battery if don’t use the device in along time.

Accessories

Only use original accessories. Check that the contents of the delivery are complete.

Trouble-shooting

Specifications

Standard list

Shenzhen PACOM Medical Instruments Co., Ltd declares that the PC868 complies with following applicable standards:

Disposal

Dispose of the device in accordance with the regulation applicable at the place of operation. Dispose of at public collection point in the EU countries—2002/96/EC WEEE Directive.
If you have any queries,please refer to the local authorities responsible for waste disposal.

Notice

• Handing of battery and wastes method,please act according to the native law to proceed to handle.
• Take out the battery if you are not going to use the unit for a long time.
To protect the environment, dispose of empty battery at your retail store or at appropriate collection sites according to national or local regulations.
Dispose of at public collection point in the EU countries—
2006/66/EC Directive.

Normalized symbols

EMC DECLATION

1) The digital thermometer needs special precautions regarding EMC and needs to be installed and put into service according to the MEC information provided in the ACCOMPANYING DOCUMENTS.
2) Wireless communications equipment such as wireless home network devices,mobile phones,cordless telephones and their base stations, walkie-talkies can effect this equipment and should be kept at least a distanced= 3.3m away from the equipment.(Note:As indicated in Table 6 of IEC 60601-1-2:2007 of ME EQUIPMENT, atypical cell phone with a maximum output power of 2W yields d = 3.3m at an IMMUNITY LEVEL of 3V/m).

Guarantee

We grant you a lifetime guarantee after the date of purchase for one year.Any damage caused by improper handling shall not be covered by the guarantee. Batter and packaging area also excluded from the guarantee. All other damage claims excluded. A guarantee claim must be submitted with the purchase receipt. Please pack your defective instrument well and send with sufficient postage to the distributor.

Shenzhen Pacom Medical Instruments Co.,Ltd.

Address: On the 8th floor of B District, B Building,No.5,Industry five road, Jiangbian Community, Songgang,
Shenzhen, China.
Tel: 86-755-32920339
Website: www.pacomsz.com

Shanghai International Holding Corp. GmbH(Europe)

Address: Eiffestrasse 80,20537 Hamburg Germany
Tel:0049-40-2513175
Fax:0049-40-255726
E-mail: shholding@hotmail.com

GLH-600 is a cleansing lotion for hands
and body. Its choice of special pearlizing
agent providesfor a luxurious look and
feel. Its pH is neutral balanced so that
repeated washings will not dry skin. Fruity
fragrances have been added to produce a
pleasant, lasting aroma.

FEATURES, ADVANTAGES AND BENEFITS
- Neutral pH
- Pearlized pink color
- Biodegradable
- No phosphates, or nonyl phenol ethoxylates

DIRECTIONS FOR USE

Apply a small amount of hand soap to wet hands.
Lather well and rinse.

SAFETY REMINDER

Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

GLH-602 is a cleansing foam for hands and
body. It naturally cleanses and moisturizes
skin with soothing naturally derived
surfactants.

FEATURES, ADVANTAGES AND BENEFITS
- Instant foam – easy to lather, easy to rinse
- No added fragrance
- Colorless (no added dye)
- pH balanced
- Biodegradable
- No phosphates, or nonyl phenol ethoxylates

DIRECTIONS FOR USE
Wet hands and apply foam. Rub hands together
and rinse with clean water.

SAFETY REMINDER
Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Your Partner In Making
Sustainable Healthy Environments

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

GLH-601 is a cleansing foam for hands and
body. It naturally cleanses and moisturizes
skin with soothing naturally derived
surfactants and refreshing jasmine scent.

FEATURES, ADVANTAGES AND BENEFITS
- Instant foam – easy to lather, easy to rinse
- Jasmine scent
- pH balanced
- Biodegradable
- No phosphates, or nonyl phenol ethoxylates

DIRECTIONS FOR USE
Apply a small amount of hand soap to wet hands.
Lather well and rinse.

SAFETY REMINDER
Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Your Partner In Making
Sustainable Healthy Environments

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

GLH-603 is a scent-free hand soap that
contains a special pearlizing agent which
provides a luxurious look and feel even
after repeated washing. Coupled with
neutral pH, it provides superior cleaning
action on skin to quickly remove greasy,
oily residues.

FEATURES, ADVANTAGES AND BENEFITS
- Neutral pH
- Pearlized natural color (no dye)
- No added fragrance
- Biodegradable
- Phosphate-free
- NPE-free

DIRECTIONS FOR USE
Apply a small amount of hand soap to wet
hands. Lather well and rinse.

SAFETY REMINDER

Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Your Partner In Making
Sustainable Healthy Environments

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

MANUAL AND TOUCH LESS BULK DISPENSERS WITH
HAND SANITIZERS IN 4L CONTAINERS

#DILO-1BLL
COLOR: White

#DILO-1NOIL
COLOR: Black

#DIMO-1BLF
COLOR: White

851 Progress Court, Oakville, Ontaria L6L 6K1           1.800.921.5527                   www.superiorsols.com

Hand Sanitizer to help reduce bacteria
that potentially can cause disease.
For use when soap and water are
not available.

Features:

- Kills 99.9% of Germs
- Alcohol antiseptic 70%
- Non-sterile topical solution

Directions:

• Place enough product on hands
to cover all surfaces. Rub hands
together until dry.

• Supervise children under 6 years
of age when using this product to
avoid swallowing.

Safety Reminder:

Before using this product please ensure
employees read and understand the
product labels and Safety Data Sheet
(SDS). Directions for use can be found
on the label. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on
the SDS sheets. SDS are available online
at superiorsols.com or by calling
1-800-921-5527. Improper use may
result in damage or injury.

Hand Sanitizer to help reduce bacteria that potentially can cause disease. For use when soap and water are not available.

- Kills 99.9% of Germs

- Alcohol antiseptic 70%

- Non-sterile topical solution

Codes:

PRWIPESD-CONT
(I bucket and i roll of 250 wipes)

PRWIPESD-CS
(Case of 6 rolls of 250 wipes)

Wipes dimensions:
6"x 6.5"

Uses:
- Surface Disinfectant
- Hand Sanitizer
- Windows
- Mirrors
- Counters

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet fermentum.

Aenean sit amet massa eu velit commodo cursus fringilla a tellus. Morbi eros urna, mollis porta feugiat non, ornare eu augue. Sed rhoncus est sit amet diam tempus, et tristique est viverra. Etiam ex tellus, sectur at dapibus id, luctus at odio. Proin mattis congue tristique.

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Our responsibilities when serving as the General Contractor include:

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet fermentum.

Aenean sit amet massa eu velit commodo cursus fringilla a tellus. Morbi eros urna, mollis porta feugiat non, ornare eu augue. Sed rhoncus est sit amet diam tempus, et tristique est viverra. Etiam ex tellus, sectur at dapibus id, luctus at odio. Proin mattis congue tristique.

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Our responsibilities when serving as the General Contractor include:

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet fermentum.

Aenean sit amet massa eu velit commodo cursus fringilla a tellus. Morbi eros urna, mollis porta feugiat non, ornare eu augue. Sed rhoncus est sit amet diam tempus, et tristique est viverra. Etiam ex tellus, sectur at dapibus id, luctus at odio. Proin mattis congue tristique.

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Our responsibilities when serving as the General Contractor include:

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.