• PULIN Nitrile Gloves Health
  • 6000 SYNTHETIC VINYL EXAM GLOVES
  • 6800 VINYL EXAMINATION DISPOSABLE GLOVES
  • 5900 Tpe Disposable Gloves

Get in Touch with us

155 Caster Avenue, Vaughan, ON L4L 5Y8

905-856-0611

info@phoenix-ds.com

PULIN Nitrile Gloves Health

PULIN Nitrile Gloves Health

Disposable Nitrile Exam Glove

Powder Free

Latex Free

Single Use
Ambidextrous

Storage

Store in cool dry place.

Do not store gloves where temperatures may rise above 40 C(104 F).

Do not store in highly humid or damp areas.

Shield from direct sunlight, fluorescent lighting, x-rays, moisture and ozone.

Caution

Nitrile gloves are not intended for use as a chemical barrier.

Do not use these gloves for protection from hazardous chemicals.

SPECIFICATION OF NITRILE DISPOSABLE GLOVES

powder-free

GLDI-520 HOSPITAL GRADE DISINFECTANT WIPES

HOSPITAL GRADE DISINFECTANT WIPES

FOR USE IN

 

- Hospital and health care settings
- Veterinary Clinics
- Funeral Homes
- Beauty Salons and Barber Shops
- Heath,Club,Gyms
- Schools
- Daycare Centers
- Grocery Stores
- Institutional and Household Kitchen
- Residences
- Transportation Terminals
- Offices

 

CLEANS,DISINFECTS & DEODORIZES
Kills 99% of Bacteria in just 60 Seconds!

Available in 2
practical sizes !

80 Wipes

GLDI-520-12S80

160 Wipes

GLDI-520-61S60

STRONG DEPENDABLE WIPES

Effective disinfectant without residue.

INFORMATION

1-800-921-5527
info@superiorsols.com
www.superiorsols.com

GLDI-520 SANY+ HOSPITAL GRADE DISINFECTANT WIPES

SANY+ HOSPITAL GRADE DISINFECTANT WIPES

FOR USE IN:

 

- Hospital and health care settings
- Veterinary Clinics
- Funeral Homes
- Beauty Salons and Barber Shops
- Heath,Club,Gyms
- Schools
- Daycare Centers
- Grocery Stores
- Institutional and Household Kitchen
- Residences
- Transportation Terminals
- Offices

DISINFECTANT WIPES

Sany+ Disinfectant Wipes are pre-moistened wipes that kill 99.9% of Bacteria in just 60 Seconds! Clean and disinfect in one easy step, just pull, wipe and toss.

Drections:

Use one Sany+ Disinfectant Wipe to disinfect.
Flip open dispensing tab and remove lid. Thread
center wipe corner through slits in lid center.
DO NOT PUSH FINGER THROUGH OPENING.
Replace lid. Dispense wipes by pulling out at an
angle. The next wipe pops up automatically.
Snap flip lid down when finished, to retain
moisture. Dispose of used wipes in trash.
Do not flush.

Disinfecting

To disinfect hard, non-porous surfaces,
thoroughly wet the surface to be treated.
Treated surface must remain visibly wet for
disinfecting. Use enough wipes for treated
surface to remain visibly wet for 5 minutes.
For heavily soiled surfaces, clean before
following disinfecting instructions.

SANY+ DISINFECTANT WIPES
DIN: 02509709
Product Code: GLDI-520-12S80
GLDI-520-6S160
Unit Size: 80 Wipes
160 Wipes
Case Size: 12 x 80 Wipes
6 x 160 Wipes
Physical Appearance: Wipes
Colour White

To shop now, visit: www.superiorsols.com or call: 1-800-921-5527

Infrared thermometer PC 868

Infrared thermometer PC 868

User's Manual

Please read before use!

Summary of Infrared Thermometer

Thank you for choosing our Infrared Thermometer. The PC868 Infrared Thermometer is used to measure an objects temperature based on the relationship between temperature and measurable infrared radiation. Simply aim the unit’ s probe toward the surface to be measured to obtain a quick and accurate temperature.
To ensure proper use,please be sure to read this user manual carefully,paying close attention to the safety precautions.
• In order to use this product correctly,please read the user manual before use.
• In order to properly use this product,please carefully read the full text of this manual before using, in particular the “safety precautions"section.
• Please keep the instructions on the side for easy checking.

Basic principles:
All objects above absolute zero temperature emits certain percentage of infrared radiation energy based on its temperature.The amount of the radiation energy and the distribution of thewavelengthhaveverycloselyrelationship.Whenhumanforehead’stemperaturein36-37°C,it emits wavelength 9-13um of infrared radiation. Based on this principle, according to the relationship between surface forehead temperature and human forehead’s temperature,we are able to measure the human forehead’s actual temperature through measuring surface forehead temperature.

Safety precautions

Warning

• Use of this thermometer is not intended as a substitute for consultation with your physician. It is dangerous for user to perform a self-evaluation and self-treatment based on the measuring result. Be sure to follow doctor’s instruction.
• Keep the thermometer out of reach of children. For accidental swallow of battery or other component, please consult the doctor at once.
• Don't throw the battery into fire.

Notice

• The device is precision instrument,don’t drop,tramp or impose any vibration or impact on the thermometer.
• Do not touch the lens of the probe with your fingers,and do not dissemble the device by yourself.
• Before measuring forehead temperature,make sure the hair re-moved, sweat dried.
• After you do some exercise,eating and bathing,you should stay still indoor about 30 minutes before measurement.
• To make the measurement data reliable and stable, when ambient temperature varies a lot,the thermometer should be placed indoors for about 30 minutes before using.
• When we measure somebody continuously,the temperature should be measured every minute,if you need to measure yourself Continuously for a short time,there are some slight errors when you read the temperature,which is a normal phenomenon.At this time,we should choose the average.We recommend that you measure yourself continuously maximum of three in a unit of time,and because the temperature of the human will conduct to the thermometer,it may affect the accuracy of measurement.
• There is no absolute standard about the temperature of the human, so please try to collect the recording of Individual temperature in the usual,as a reference for having a fever or not.
• Do not measure the sites of scarred tissue or tissue compromised by skin disorders,because sensing body temperature from sites of scarred tissue or tissue compromised by skin disorders.
• Do not measure the site of forehead temperature if that patients has trauma on forehead.
• Do not measure if that patient is treated with certain drug therapies.
• Do not immerse the device into water or any other liquid,and not directly sunlight exposure.
• Do not use a mobile or mobile or cordless hone near the thermometer when measuring.
• Body temperature may increase in the drug with in the effort time limit. Please don’t measure.
• In order to ensure the accuracy of measurement data,please don’t take measurement of body temperature in strong electro- magnetic interference environment (such as microwave, high frequency equipment operation environment).
• Do not disassemble, repair, or modify the unit.
• This thermometer only a personal device,please do not user with others.
• Not touch the battery output when measuring.
• The thermometer must be stored according to the technical specifications.
• The materials (ABS) of expect contact with patient had passed the ISO 10993-5 and ISO 10993-10 standard test,no toxicity,allergy and irritation reaction. The are compliance with the MDD requirements. Based on the current science and technology, other potential allergic reactions are unknown.
• The patent is an intended operator. The patient can measure, read data and replace battery under normal circumstances and maintain the device and its accessories according to the user manual.
• ThedeviceisnotintendedforPATIENTtransportoutsideahealthcarefacility.

Recommendations

1) Don’t use this thermometer for other purposes.
2) It is forbidden to leave the product exposed to any chemical solvent, direct sunshine or high temperature.
3) Don’t expose the thermometer under direct sunlight longtime so as not to damaged the battery.
4) Do not measure while talking on the phone.
5) Please report to MANUFACTURER if any unexpected operation or events occur.

Intended use

This thermometer is intended with non-contact to measurement forehead temperature at home or hospital,including anyone,such as infants, children and adults.
For the safety reason,children or the baby’s temperature must be measured by parent or adults.

Temperature measurement mode and range description

The infrared thermometer has the following measurement mode:
1) Forehead temperature measurement mode--measure the skin surface of human forehead’s temperature accurately,taketheplaceoftraditionalmercurythermometerandelectricalthermometer.
2) Object temperature measurement mode—you can measure the surface temperature of object,such as ambient,bathwater and milk temperature etc.

Normal temperature range for different measuring position

Measuring position Nomal temperature (W) Nomal temperature (°F)
Anus 36.6-38.0 97.9-100.4
Oral 35.5-37.5 95.9-99.5
Armpit 34.7-37.3 94.5-99.1
Forehead 35.8-38.0s 96.4-100.4

Normal forehead temperature range for different ages

Ages Nomal temperature (W) Nomal temperature (T}
0-2 years old 36.4-38.0 97.5-100.4
3-10 years old 36.1-37.8 97.0-100.0
11-65 years old 35.9-37.6 96.6-99.7
> 65 years old 35.8-37.5 96.4-99.5

NOTE: The normal temperature and difference between the different body parts is individual. The define yours,measure your temperature for atleast 2 weeks at the same ear canal,forehead position and time.
NOTE: When consulting your physician, communicate that the infrared thermometer PC 868 temperature is a temperature measured which position,note the individual’s normal infrared thermometer PC 868 temperature range as additional reference.
NOTE: Because the forehead temperature is affected obviously by the external environment(eg: environment,air convection and skin tone,etc),we advice that you take the forehead temperature only as reference.

Feature

• Precise non-contact measurements
• User selectable °C or°F
• Set alarm temperature value
• Automatic data hold and auto power save
• Automatic selection range and display resolution 0.1°C(0.1°F)
• 3 colors backlight
• 2 measurement mode: Forehead and surface mode

Overall description

1. IR sensor
3. Mode selection
5. UP button
7. Measurement Trigger

2. LCD display
4. Down button
6. Mode button
8. Battery cover

[LCD display description]

1. Surface mode symbol
2. Body mode symbol
3. Digital readout
4. Battery symbol

5. Memory Symbol
6. Save data readout
7. Temp.°C(Celsius)/°F(Fahrenheit)scale
8. Buzzer symbol

Operation Instruction

[Preparation]

1) Check battery
Replace the batteries to ensure power supply if there is low voltage icon for the thermometer.
2) Check sensor
If have pollution and spray,please clean it.(The cleaning method see the chapter 8 Care and Cleaning for detailed.)
If the sensor’ s lens is damaged, please stop using.
3) Check thermometer
When you press the[Power/Scan]button,the system will have self testing of software and hardware. If there are problems, LCD will display "Err" symbol. Check if the sensor laser is dirty, damaged phenomenon.
4) In order to make the accurate measuring result, put the thermometer in the measurement environment for 30 minutes.
5) Accuracy of unexpected fluctuations in ambient temperature may decrease the measurement results When the thermometer at the same measurement position display at different ambient temperature,or test temperature in front of the air conditioner,it will not be able to obtain accurate results.
6) If you want measure forehead temperature, clean forehead and arrange hair,make sure the forehead is naked and clean,in order to ensure the accuracy of measurement.

[Instruction for use]

Advice for the first use

For stable and reliable results,it is essential to check the infrared thermometer and changes as needed,as follows:

1st step: Take the temperature of a person using a conventional thermometer, you will get 37.5 °C (99.5°F) for instance.
2nd step: Take the temperature of the same person using the device keeping the 3 to Scm distance between the themometer and forehead (take care to remove any obstacle which could alter the measurement (hair, perspiration ....). If you get 37.5 °C(99.5°F), the device is properly set and ready for use. If you get a lower temperature such as 36.4 °C(97.5°F), your difference is 1.1 °C(2.25°F). You should adjust the temperature on the device and add the difference, i.e.1.1 °C(2.25°F). To do it, press the MODE button for 2 seconds, the screen displays F1, press MODE button again until you get F3, press UP button in ordar to add tha difference (in our example 1.1 °C (2.2°F).
3rd step: To check, take the temperature again using the product.

Use

Install batteries

2. For the first use or when inserting new batteries,please wait about 10minutes for the warm-up of the apparatus.
3. If the device is not used for a long time, once you turn it on again,the device will test the room temperature first and will delay turning on for one or two seconds.
4. Select body mode,aim towards the forehead,form distance of 5cm(2in),press the measuring key,the temperature is displayed immediately,accompanied by a beep sound. Making sure there is no hair,perspiration,cosmetic or cap covered on the forehead.

 

5. If the measurement temperature is 38.0°C or more(can be setting,refer to sub-clause 3)),the sound should be“be-be-be-be-be”5 repid sounds.

TEMPERATURE TAKING HINTS

- Before take the temperature, please fix the forehead hair to prevent measured deviation.

- The sweat on head or cosmetic can affect the accuracy of measurement, please maintain the cleanness of the forehead when measuring.

- It i snormal that there maybe temperature difference depending on various skin types and color ,since different skin type will reflect different voltage of infrared ray.

- Don’t use the thermometer outdoors.

6.Select object mode for measuring room temperature,surface temperature etc.

TEMPERATURE TAKING HINTS

- For heat-insulated object, please don't measure the surface.

- For the hot liquid, please do not directly measure the surface, because the hot steam fog can condense in the sensor lens and cause the measurement deviation.

Setting operation

Mode codefunctionOperation step
1F1Set °C/°F scalePress MODE button for 2 seconds,the screen will display F1 on the bottom right,press UP or DOWN button can change temperature unit for °C or °F
2F2Set alarm temp.Press MODE button for 2 seconds,the screen display F1, press MODE button to get F2, select UP to increase the threshold by 0.1s(0.1°F),DOWN to reduce it by 0.1°C(0.1°F).The alarm threshold default value is 38.0°C(100.4°F).
3F3Set differencePress MODE button for 2 seconds, the screen display F1, press two times to get F3,select UP to increase the difference by 0.1°C(0.1°F),DOWN to reduce it by 0.1°C(0.1°F).In the case of seasonal or environment changes a verification and adjustment should be carried out.
Note: This function is only effective body.
4F4Set buzzer on/offPress MODE button for 2 seconds,the screen display F1, press 3 times to get F4. Select UP to turn on the buzzer,press DOWN to stop it.
5 Measurement There are 2 measurement modes for this device. That is forehead, surface. It is able to take the body temperature of human beings, take the temperature of an area or an object, a food a liquid or a room.

Forehead mode: Put the mode selection button on the right, measuremnet range 32.0 to 43.0°C(86.0 to 109.4°F)

Surface mode: Put the mode selection button on the right, measurement range 0 to 100°C(32.0 to 212.0°F)
6 3 colors backlight In body mode, the device s able to judge whether a fever or not by different color of backlight:
32.0 to 43.0°C(86.0 to 109.4°F)-Green
37.5 to 37.9°C(99.5 to 100.2°F)-Orange
38.0 to 43.0°C(100.4 to 109.4°F)-Red

In surface mode, the backlight always keeps green
7 Data memory Data memory automatically after temperature measurements, which will display at the right corner of LCD. Press UP or DOWN button to display the last temperature measurement .

--Range of alarm temperature
When into the“F-2”mode,the range of settable alarm temperature is from 37.6°C(99.7°F)to 43.0°C(109.4°F).
-Range of temperature difference
When into the“F-3”mode,the range of settable temperature difference is from 5°C(9°F) to-5°C(-9°F).

Temperature measuring

--Taking Temperature in Forehead Temperature Mode (Adjusted Mode)
1. Setup the measurement mode to“Body mode”(the setup step see the above “2) Function Setup mode”;
2. Make sure the distance between thermometer and forehead is 3-5 cm,and press the button of[Power/Scan]directly to measure the forehead temperature.
3. When you hear one beep sound,the LCD will show the result.

TEMPERATURE TAKING HINTS

- Before take the temperature,please fix the forehead hair to prevent measured devialion.

- The sweat on head or cosmetic can affect the accuracy of measurement, please maintain the cleanness of the forehead when measuring..

- It is normal that there may be temperature difference depending on various skin types and color, since different skin type will reflect different voltage of infrared ray.

- Don't use the thermometer outdoors.

NOTE:

1. When measuring, if the environment exceed the 10-40°C range will be showing Err;
2. If the measured temperature result is > 32.0°C,the LCD will be showing Lo;
3. If the measured temperature result is > 43.0°C,the LCD will be
showing Hi;
4. If the measured temperature result is >= 38.0°C,the buzzer will be send out“Beep—Beep—Beep”,along one and two short ones.
5. We recommend measurement for 3 times to reference,and keep the interval between the two measurements by 5 minutes atleast.

-Taking Temperature in Surface Temperature Mode(Direct Mode)
1. Setup the measurement mode to“Surface mode”(the setup step see the above “2) Function Setup mode”
2. Aim the probe tip at the object which will be measured.
3. Press [Power/Scans button, then the measurement completed. It will show the measurement data after a “bi”sound.
4. If the measured temperature is higher than 100°C, display “Hi”. If the measured temperature is below 0°C, display“Lo”.

TEMPERATURE TAKING HINTS

- For heat-insulated object, please don’t measure the surface.

- For the hot liquid, please do not directly measure the surface,because the hot steam fog can condense in the sensor lens and cause the measurement deviation.

Automatic shutdown

If you do nothing after the temperature measurement completed and 15 seconds later, the thermometer will automatically shutdown.

Memory function

In the power-on state, press the Up/Down button into memory query mode,the LCD will be showing the recorded values or“---“ symbol if not record accompanied with memory M symbol.The PC 868 can restore up to 99 sets data. the query interface can display memory seriaI number,body mode and recorded temperature values.
Remark:The temperature result of surface mode cannot be saved. And the abnormal body temperature result cannot be saved too (such as Lo, Err or Hi).

Backlight function

The backlight will be according to the different measuring temperature to lighting different color . The detailed as below table:

Measuring temperature Backlight Lighting time
° 37.5W Green backlight 7s
37.5 to 37.9V Orange backlight 7s
?38.0s Red backlight 7s
Remarks:This specification of this table only for the factory default state.If the user into the setup mode to setting the orange or red backing temperature, then will compliance with thes etting result.

Restore the factory default function

Press the [Setup] button for 5s to restore the factory default status. The factory default setup is "C” and “Body measurement” mode.

Battery installment and replacement

1. When the quantity of electric charge is not sufficient,the icon of low battery will appear on the lower part of the screen. Though the battery still can be used,it would be perfect to replace it.
2. When the quantity of electric charge of the battery is lower than them minimal value,“Lo”symbols will bed is played on the screen, and battery icon flashes and the sound of “Beep” is sent out.
Unless you change a new battery,you cannot use the thermometer to conduct measurement.
3. Operation of changing battery.
4. Take out the old battery: Open the battery cap;put 2 new AAA batteries on with correct cathode direction into the battery seat.

Notice:

◦ Please observe the related national laws of disposing the abandoned battery and don’t litter to the garbage can.
◦ Please take out the battery if the device is not used for long periods of time.
◦ Please don’t put the battery in the fire.

Care and cleaning

• Probe tip (lens) is a most precise part in the thermometer.Please keep clean and entirety in order to assure the accuracy of figure.
• The probe tip and lens are the most delicate part of the thermometer. It has to be clean and intact to ensure accurate readings.
• If the thermometer is ever accidentally used clean the probe and lens as follows:
• Very gently wipe the surface with a cotton swab or soft cloth moistened with alcohol. After the alcohol has completely dried out.
• If the lens is damaged,contact the distributor.
Clean the unit body:
• Use a soft,dry cloth to clean the thermometer display and unit body.
• If very dirty,use a soft with alcohol to cleaning.

Notes:

◦ Don not use abrasive cleaners.
◦ Don’t use other non-recommended methods to perform disinfect.
◦ Non-waterproof, don’t use the abrasive cleaner to clean the product, don’t drop the thermometer in the water or the other liquid.

Maintenance

1) We don ot authorize any institution or individual to maintain and repair of the product. If you suspect that the products have any questions,please contact the manufacturer or distributor to handle the case.
2) The user must not attempt any repairs to the device or any of its accessories. Please contact the retailer for repair.
3) Opening of the equipment by unauthorized agencies is not allowed and will terminate any claim to warranty.
WARNING: No modification of this equipment is allowed!

Calibration

The thermometer is initially calibrated at the time of manufacture.If this thermometer is used according to the use instruction, periodic re-adjustment is not required. If any time your question the accuracy of measurement, please contact distributor or manufacturer, the contact information see last page.

Storage

1) Don’t put the thermometer under the sunshine, high temperature and moist environment or some place which may be get in touch with fire or is vulnerable to vibration.
2) Take out the battery if don’t use the device in along time.

Accessories

Only use original accessories. Check that the contents of the delivery are complete.

Quantity Parts
1pc PC868 device
2pcs AAA battery
1pc User Manual

Trouble-shooting

Troubles or error message Checklists or situation Countermeasures or solution
No response/Automatically reset The battery are used up?

Battery in wrong polarity or type?

Poor battery contact
Replace new batteries.

Take out the battery and replace new ones.
Take out batteries and reinsert it correct.
The thermometer show the symbol"Hi" Temperature hampered by an air flux.

In the forehead measurement mode:
--Temperature readings too close together.
--Measured the other object,such as te sunlight, the air from the fireplace.
Hi:Higher than 43.0°C;

In the object measurement mode:
--Temperature reading too close together.
--The object temperature is higher than 100°C
Please leave the status and wait for 30 minutes to measure.
Re-measure according to the manual.
The thermometer show the symbol "Lo" The hair and sweat prevent the temperature achievent.

Temperature hampered by an air flux.

In the forehead measurement mode:
--The measuring distance is too far.
--Measured the other object, such as the air from the air conditioner .
Lo:Less than 32.0°C

In the object measurement mode:
--The measuring distance is too far.
--Have water vapor condeness on the lens.
Lo:Less than 0°C
The ambient temperature is beyond of range of measurement (10°C-40°C)

The sensor or hardware is damaged
Keep thethermometer in the room Whose Temperature is (10°C-40°C) for 30 minutes

Excluding the possibility of temperature allowance first, then send the device to your dealer for repair
Lower battery, however you can't use it Replace the new battery

Specifications

Device name Infrared Thermometer
Model PC868
Measurement mode Forehead and object temperature modes
Power supply d.c.3V, 2 pcs AAA battery
Measuring range: For forehead temperature: 82.0-43.0°C
For object surface temperature: 0-100°C
Measuring accuracy:
(At laboratory conditions)
for forehead temperature:
+- 0.2 during 35.5°C -42.0°C;
+- 0.3 during 32.0°C -35.4°C and 42.1°C -43.0°C
Clinical repeatability Within +- 0.3°C
Resolution of display 0.1°C/0.1°F
Operation condition 10-40°C, Relatve humidity 15-85%, 70-160KPa
Storage condition -25-50°C,Relative humidity 15-85%, 70-106KPa
Size 149(L)x95(W)x45(H)mm
Weight Approx. 145g(including battery)
High body temperature >=38°C
Grade of aerproof IP22
Electric shock Internally poweres ME equipment
Appled part Type BF applied part, including the whole unit
Mode of operation Continuous operation
Product life 5 years
Software version V1.0

Standard list

Shenzhen PACOM Medical Instruments Co., Ltd declares that the PC868 complies with following applicable standards:

EN 980
Symbols for use in the labeling of medical devices
EN 1041
Information supplied by the manufacturer with medical devices
EN 60601-1
Medical electrical equipment Part 1: General requirements for basic safety and essential performance
EN 60601-1-2
Medical electrical equipment -- Part 1-2: General requirements for basic safety and essential performance - Collateral standard: Usability
EN60601-1-6
Medical electrical equipment-Part1-6: General requirements for basic safety and essential performance—Collateral standard: Usability
EN 60601—1—11
Medical electrical equipment - Part 1-11: General requirements for basic safety and essential performance — Collateral standard: Requirements for medical electrical equipment and medical electrical systems used in home healthcare environment
EN 12470-5
Clinical thermometers—Part 5: Performance of infra-red ear thermometers (with maximum device)
ISO 80601-2-56
Medical electrical equipment part 2-56: particular requirements for basic safety and essential performance of clinical thermometers for body temperature measurement
EN62304
Medical device software - Software life-cycle processes
EN62366
Medical devices—Application of usability engineering to medical devices
ENISO10993—1
Biological evaluation of medical devices-Part1:Evaluation and testing within a risk management process

Disposal

Dispose of the device in accordance with the regulation applicable at the place of operation. Dispose of at public collection point in the EU countries—2002/96/EC WEEE Directive.
If you have any queries,please refer to the local authorities responsible for waste disposal.

Notice

• Handing of battery and wastes method,please act according to the native law to proceed to handle.
• Take out the battery if you are not going to use the unit for a long time.
To protect the environment, dispose of empty battery at your retail store or at appropriate collection sites according to national or local regulations.
Dispose of at public collection point in the EU countries—
2006/66/EC Directive.

Normalized symbols

Follow operating instructions
BF type applied part
Disposal in accordance with Directive 2002/96/EC (WEEE)
Complies with the European Medical Device Directive (93J42/EEC and amended Directive 2007J47/'EC.Notified Body is SGS FIMKO Yo
Manufacturer information:The manufacturer is: Shenzhen PACOM Medical Instruments Co.,Ltd.
Authorized representative in the European Community. The European representative is: Shanghai International Holding Corp. GmbH(Europe)
IP code of the device:thisdevice’s grade of against ingress of solid foreign objects-- >=12.5mm diameter (and the against access to hazardous parts with finger);the grade of water proof is dripping (150 tilted).
Batch code
Date of manufacture

EMC DECLATION

1) The digital thermometer needs special precautions regarding EMC and needs to be installed and put into service according to the MEC information provided in the ACCOMPANYING DOCUMENTS.
2) Wireless communications equipment such as wireless home network devices,mobile phones,cordless telephones and their base stations, walkie-talkies can effect this equipment and should be kept at least a distanced= 3.3m away from the equipment.(Note:As indicated in Table 6 of IEC 60601-1-2:2007 of ME EQUIPMENT, atypical cell phone with a maximum output power of 2W yields d = 3.3m at an IMMUNITY LEVEL of 3V/m).

Guarantee

We grant you a lifetime guarantee after the date of purchase for one year.Any damage caused by improper handling shall not be covered by the guarantee. Batter and packaging area also excluded from the guarantee. All other damage claims excluded. A guarantee claim must be submitted with the purchase receipt. Please pack your defective instrument well and send with sufficient postage to the distributor.

Shenzhen Pacom Medical Instruments Co.,Ltd.

Address: On the 8th floor of B District, B Building,No.5,Industry five road, Jiangbian Community, Songgang,
Shenzhen, China.
Tel: 86-755-32920339
Website: www.pacomsz.com

Shanghai International Holding Corp. GmbH(Europe)

Address: Eiffestrasse 80,20537 Hamburg Germany
Tel:0049-40-2513175
Fax:0049-40-255726
E-mail: shholding@hotmail.com

GLH-600 LOTION HAND SOAP (SCENT FREE)

GLH-600 LOTION HAND SOAP (SCENT FREE)

GLH-600 is a cleansing lotion for hands
and body. Its choice of special pearlizing
agent providesfor a luxurious look and
feel. Its pH is neutral balanced so that
repeated washings will not dry skin. Fruity
fragrances have been added to produce a
pleasant, lasting aroma.

FEATURES, ADVANTAGES AND BENEFITS
- Neutral pH
- Pearlized pink color
- Biodegradable
- No phosphates, or nonyl phenol ethoxylates

DIRECTIONS FOR USE

Apply a small amount of hand soap to wet hands.
Lather well and rinse.

SAFETY REMINDER

Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Description
Physical State and Appearance Thick opaque liquid
Color Pink
Sediment None
Odor Fruity
pH (concentrated) 6.5 – 7.0
Specific Gravity 1.04 – 1.06
Flash Point None
Product Code Package Size
GLH-600-4S4 4 X 4L Bottles

Your Partner In Making
Sustainable Healthy Environments

 

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

Superiorsols.com | 851 Progress Court, Oakville, ON L6L 6K1 |1-800-921-5527

GLH-602 FOAMING HAND SOAP (SCENT FREE)

GLH-602 FOAMING HAND SOAP (SCENT FREE)

GLH-602 is a cleansing foam for hands and
body. It naturally cleanses and moisturizes
skin with soothing naturally derived
surfactants.

FEATURES, ADVANTAGES AND BENEFITS
- Instant foam – easy to lather, easy to rinse
- No added fragrance
- Colorless (no added dye)
- pH balanced
- Biodegradable
- No phosphates, or nonyl phenol ethoxylates

DIRECTIONS FOR USE
Wet hands and apply foam. Rub hands together
and rinse with clean water.

SAFETY REMINDER
Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Description
Physical State and Appearance Transparent liquid
Color Colourless
Sediment None
Odor Scent Free
pH (concentrated) 6.5 – 7.5
Specific Gravity 1.024 – 1.044
Flash Point None
Product Code Package Size
GLH-602-4S4 4 X 4L Bottles

Your Partner In Making
Sustainable Healthy Environments

 

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

Superiorsols.com | 851 Progress Court, Oakville, ON L6L 6K1 |1-800-921-5527

GLH-601 FOAMING HAND SOAP (JASMINE)

GLH-601 FOAMING HAND SOAP (JASMINE)

GLH-601 is a cleansing foam for hands and
body. It naturally cleanses and moisturizes
skin with soothing naturally derived
surfactants and refreshing jasmine scent.

FEATURES, ADVANTAGES AND BENEFITS
- Instant foam – easy to lather, easy to rinse
- Jasmine scent
- pH balanced
- Biodegradable
- No phosphates, or nonyl phenol ethoxylates

DIRECTIONS FOR USE
Apply a small amount of hand soap to wet hands.
Lather well and rinse.

SAFETY REMINDER
Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Description
Physical State and Appearance Transparent liquid
Color Green
Sediment None
Odor Floral (Jasmine)
pH (concentrated) 6.5 – 7.5
Specific Gravity 1.024 – 1.044
Flash Point None
Product Code Package Size
GLH-601-4S4 4 X 4L Bottles

Your Partner In Making
Sustainable Healthy Environments

 

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

Superiorsols.com | 851 Progress Court, Oakville, ON L6L 6K1 |1-800-921-5527

GLH-603 LOTION HAND SOAP (FRUIT SCENT)

GLH-603 LOTION HAND SOAP (FRUIT SCENT)

GLH-603 is a scent-free hand soap that
contains a special pearlizing agent which
provides a luxurious look and feel even
after repeated washing. Coupled with
neutral pH, it provides superior cleaning
action on skin to quickly remove greasy,
oily residues.

FEATURES, ADVANTAGES AND BENEFITS
- Neutral pH
- Pearlized natural color (no dye)
- No added fragrance
- Biodegradable
- Phosphate-free
- NPE-free

DIRECTIONS FOR USE
Apply a small amount of hand soap to wet
hands. Lather well and rinse.

SAFETY REMINDER

Before using this product please ensure
employees read and understand the product
labels and Material Safety Data Sheet.
Directions for us can be found on the label as
well as the MSDS. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on the
MSDS sheets. MSDS are available online at
greenlabscs.com or by calling 1-800-921-5527.
Improper use may result in damage or injury.

Description
Physical State and Appearance Thick and opaque liquid
Color Natural
Sediment None
Odor Characteristic (scent free)
pH (concentrated) 6.5 – 7.0
Specific Gravity 1.01 – 1.06
Viscosity 1,000 – 1,200 cps
Product Code Package Size
GLH-603-4S4 4 X 4L Bottles

Your Partner In Making
Sustainable Healthy Environments

 

We are committed to ensuring our cleaning
solutions make your workplace clean, green and
healthy – while reducing costs, enhancing
employee safety, and promoting the
sustainability of your cleaning, facility care and
sanitation process.

Superiorsols.com | 851 Progress Court, Oakville, ON L6L 6K1 |1-800-921-5527

HAND SANITIZING SOLUTIONS

HAND SANITIZING SOLUTIONS

MANUAL AND TOUCH LESS BULK DISPENSERS WITH
HAND SANITIZERS IN 4L CONTAINERS

• 1000 ml format

• Integrated lock

• Choice of a white or black dispenser

ALSO AVAILABLE WITH A STAND

USE WITH
A CERTIFIED
HAND SANITIZER!

DISPENSERS

 

MANUAL
DISPENSER

 

TOUCH LESS
LOTION DISPENSER

#DILOAUT-WH

#DILO-1BLL
COLOR: White

 

#DILO-1NOIL
COLOR: Black

 

#DIMO-1BLF
COLOR: White

SANITATION STEP

SANITATION STEP

SPECIFICATIONS
MATERIAL: Mild Steel
SURFACE TREATMENT: Outdoor Powder Coating
OVERALL SIZE: 1100 x 300 x 300 mm (HWD)-
43,3’’ x 11.8’’ x 11.8’’
WEIGHT: 8 kg
BASE SIZE: 300 x 300 mm (LW) - 11.8’’ x 11.8’’
BASE THICKNESS: 5 mm
COLOUR: Black
MAX BOTTLE HEIGHT: 300 mm – 11.8’’
MAX BOTTLE DIAMETER: 100 mm – 3.9’’
ADJUSTABLE: Bottle size form 473 ml to 1L
PACKAGE: Carton Box/1pcs/ctn
PACKAGE SIZE: 1110 x 340 x 155 mm (LWH)
43.7’’ x 13.3’’ x 6.1’’

851 Progress Court, Oakville, Ontaria L6L 6K1           1.800.921.5527                   www.superiorsols.com

GLS-550 Gel Hand Sanitizer

GLS-550 Gel Hand Sanitizer

Hand Sanitizer to help reduce bacteria
that potentially can cause disease.
For use when soap and water are
not available.

Features:

- Kills 99.9% of Germs
- Alcohol antiseptic 70%
- Non-sterile topical solution

Directions:

• Place enough product on hands
to cover all surfaces. Rub hands
together until dry.

• Supervise children under 6 years
of age when using this product to
avoid swallowing.

Safety Reminder:

Before using this product please ensure
employees read and understand the
product labels and Safety Data Sheet
(SDS). Directions for use can be found
on the label. Additionally, employees can
find hazard warnings, precautionary
statements and first aid procedures on
the SDS sheets. SDS are available online
at superiorsols.com or by calling
1-800-921-5527. Improper use may
result in damage or injury.

For Use On:

GLS-550 GEL HAND SANITIZER
NPN: 80098669
Product Code: GLS-550-1S12
GLS-550-378S4
Unit Size: 1L
3.78L
Case Size: 12 x 1L Bottles
4 x 3.78L Bottles
Physical Appearance: Gel
Colour: Colourless
Odour: Fragrance free
pH (Concentrated): 6.5 – 7.5
Specific Gravity: 0.875 g/mL

GLS-550 Gel Hand Sanitizer / Gel desinfectant pour les mains

GLS-550 Gel Hand Sanitizer / Gel desinfectant pour les mains

 

 

Hand Sanitizer to help reduce bacteria that potentially can cause disease. For use when soap and water are not available.

- Kills 99.9% of Germs

- Alcohol antiseptic 70%

- Non-sterile topical solution

Make your multi-purpose wipes

Make your multi-purpose wipes

Codes:

PRWIPESD-CONT
(I bucket and i roll of 250 wipes)

PRWIPESD-CS
(Case of 6 rolls of 250 wipes)

Wipes dimensions:
6"x 6.5"

Uses:
- Surface Disinfectant
- Hand Sanitizer
- Windows
- Mirrors
- Counters

- Kitchen
- Bathroom
- Walls
- Garage
- Cars

GLDI-H202 DISINFECTANT CLEANER FORMULATED WITH HYDROGEN PEROXIDE

GLDI-H202 DISINFECTANT CLEANER FORMULATED WITH HYDROGEN PEROXIDE

GLDI-H202 Disinfectant cleans by removing tough soils such as dirt, grime, mold and mildew.
GLDI-H202 Disinfectant reduces odor-causing bacteria, leaving surfaces smelling clean and
fresh. Its non-abrasive formula is designed for use on hard surfaces associated with non-food
contact countertops, wall, floors and restroom surfaces.

Cleaner:

One-Step Cleaner Disinfectant with
powerful surfactant (detergents)
simplifying cleaning saving time and
money.

Responsible:

Designed to be easier on surfaces,
people and animals. Users are not
exposed to VOC’s (volatile organic
compounds).

Sustainable:

Hydrogen peroxide breaks down into
water and oxygen reducing
environmental impact and improving
the environment.

Compatible:

Designed to be compatible with a wide
range of materials, protecting your
assets.

GLDI-H202 HOSPITAL GRADE PEROXIDE GENERAL PURPOSE DISINFECTANT CLEANER
DIN 02458497 - RTU
DIN 02447185 - CONCENTRATE
UL 2794
Format size: 740mL - Ready to Use
2L - Concentrate
4L - Concentrate
Product code: GLDI-H202-740S12
GLDI-H202-2S4
GLDI-H202-4S4
Packaging: 12 x 740mL
4 x 2L
4 x 4L
Shelf life: 1 Year, 2 Months

For Use In:

• Schools
• Daycare centres
• Office buildings
• Supermarkets
• Restaurants
• Hospitals
• Long term care facilities

For Use On:

• Walls
• Floors
• Counters, tables and other hard surfaces
• Stainless Steel
• Grout
• Concrete

• Virucidal

• Fungicidal

• Bactericidal

• Kills Mold & Mildew

6000 SYNTHETIC VINYL EXAM GLOVES

6000 SYNTHETIC VINYL EXAM GLOVES

Powder free, Latex free, Ambidextrous, Non sterile, Single use

  • The donning feeling is better than vinyl gloves
  • The wearing time is better than nitrile gloves
  • Better cost-performance, effectively reduce customers’ cost
  • PU coating, with no protein in it, allergy risk is reduced effectively
  • Better protection, good resistance of acid, alkali and oil
MAIN FEATURES
#MODEL MATERIAL COLOR UN/BOX BOX/CASE UN/CASE
6000 COMPOUND OF VINYL-BASED HYBRID BLUE 100 10 1000
SPECIFICATIONS
#ITEM SIZE THICKNESS
6000S SMALL 3 MIL
6000M MEDIUM 3 MIL
6000L LARGE 3 MIL
6000XL X-LARGE 3 MIL

6800 VINYL EXAMINATION DISPOSABLE GLOVES

6800 VINYL EXAMINATION DISPOSABLE GLOVES

Vinyl clear, powder free

  • Vinyl clear
  • Powder free
  • Latex free
  • Ambidextrous
  • Non-sterile
  • Single use

CERTIFICATIONS

  • Approved by the Canadian Food Inspection Agency
  • Evaluated and accepted by Health Canada for medical examination.
MAIN FEATURES
#MODEL MATERIAL COLOR UN/BOX BOX/CASE UN/CASE
6800 VINYL, POWDER FREE CLEAR 100 10 1000
SPECIFICATIONS
#ITEM SIZE THICKNESS
6800S SMALL 4.2 GRAM
6800M MEDIUM 4.2 GRAM
6800L LARGE 4.2 GRAM
6800XL X-LARGE 4.2 GRAM

5900 Tpe Disposable Gloves

5900 Tpe Disposable Gloves

Stretch polymer, powder free

  • TPE Stretch polymer
  • Extensible
  • Powder free
  • Latex free
  • Hybrid
  • Clear
MAIN FEATURES
#MODEL MATERIAL COLOR UN/BOX BOX/CASE UN/CASE
5900 TPE STRETCH POLYMER CLEAR 100 10 1000
SPECIFICATIONS
#ITEM SIZE WEIGHT (G)
5900S SMALL 1.8+/-0.2
5900M MEDIUM 2.0+/-0.2
5900L LARGE 2.2+/-0.2
5900XL X-LARGE 2.4+/-0.2

Emergency Lighting

Commercial Lighting

Horticultural

LED Bulbs

LED Bulbs

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet fermentum.

Aenean sit amet massa eu velit commodo cursus fringilla a tellus. Morbi eros urna, mollis porta feugiat non, ornare eu augue. Sed rhoncus est sit amet diam tempus, et tristique est viverra. Etiam ex tellus, sectur at dapibus id, luctus at odio. Proin mattis congue tristique.

Proconstruction Services

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Our responsibilities when serving as the General Contractor include:

  • Providing all materials, labor equipment.
  • Eget Egestas. Aenean varius ex ut ex laoreet Aenean.
  • Aenean varius ex ut ex laoreet Aenean fermentum.

Reliable & Experienced

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

  • Providing all materials, labor equipment.
  • Eget Egestas. Aenean varius ex ut ex laoreet Aenean.
  • Aenean varius ex ut ex laoreet Aenean fermentum.
  • Inspections And Occupancy Permit
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Pharmaceutical Advice
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Medical Counseling
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Rehabilitation Center
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

Decorative

Decorative

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet fermentum.

Aenean sit amet massa eu velit commodo cursus fringilla a tellus. Morbi eros urna, mollis porta feugiat non, ornare eu augue. Sed rhoncus est sit amet diam tempus, et tristique est viverra. Etiam ex tellus, sectur at dapibus id, luctus at odio. Proin mattis congue tristique.

Proconstruction Services

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Our responsibilities when serving as the General Contractor include:

  • Providing all materials, labor equipment.
  • Eget Egestas. Aenean varius ex ut ex laoreet Aenean.
  • Aenean varius ex ut ex laoreet Aenean fermentum.

Reliable & Experienced

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

  • Providing all materials, labor equipment.
  • Eget Egestas. Aenean varius ex ut ex laoreet Aenean.
  • Aenean varius ex ut ex laoreet Aenean fermentum.
  • Inspections And Occupancy Permit
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Pharmaceutical Advice
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Medical Counseling
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Rehabilitation Center
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

Exterior Lighting

General Contracting

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet fermentum.

Aenean sit amet massa eu velit commodo cursus fringilla a tellus. Morbi eros urna, mollis porta feugiat non, ornare eu augue. Sed rhoncus est sit amet diam tempus, et tristique est viverra. Etiam ex tellus, sectur at dapibus id, luctus at odio. Proin mattis congue tristique.

Proconstruction Services

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

Our responsibilities when serving as the General Contractor include:

  • Providing all materials, labor equipment.
  • Eget Egestas. Aenean varius ex ut ex laoreet Aenean.
  • Aenean varius ex ut ex laoreet Aenean fermentum.

Reliable & Experienced

Proin sagittis feugiat elit finibus pretium. Donec et tortor non purus vulputate tincidunt. Cras congue posuer eros eget egestas. Aenean varius ex ut ex laoreet Aenean the fermentum.

  • Providing all materials, labor equipment.
  • Eget Egestas. Aenean varius ex ut ex laoreet Aenean.
  • Aenean varius ex ut ex laoreet Aenean fermentum.
  • Inspections And Occupancy Permit
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Pharmaceutical Advice
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Medical Counseling
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book

  • Rehabilitation Center
    • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book